Produtos
O programa Melpool consiste em produtos, cuidadosamente sintonizados entre si.
Quickly dissolving non-stabilised sanitiser in granular form for shock treatment and continuous disinfection in soft and medium hard water
Continuous disinfection (stabilised water): 20-30 g per 10 m³ of water every 1 or 2 days.
Non-stabilised water: 30-50 g per 10 m³ of water every day (divided into 2 equal doses in the morning and evening).
Shock treatment/ presence of algae: 50-80 g per 10 m³ of water. After a shock treatment the pool should not be used for several hours. Maintain the chlorine level between 1 and 2 ppm in stabilised water, and between 0,5 and 1 ppm in unstabilised water. 16 g of product in 10 m³ of water will increase the chlorine level by 1 ppm (mg/l).
Non-stabilised sanitiser tablets of 20 g for continuous disinfection in soft and medium hard water
Continuous disinfection (stabilised water): 1-2 tablets per 10 m³ of water every 1 or 2 days.
Non-stabilised water: 2-3 tablets per 10 m³ of water every day (divided into 2 equal doses in the morning and evening).
Shock treatment/ presence of algae: 3-4 tablets per 10 m³ of water. After a shock treatment the pool should not be used for several hours.
Maintain the chlorine level between 1 and 2 ppm in stabilised water, and between 0,5 and 1 ppm in unstabilised water. 1 Tablet of product in 10 m³ of water will increase the chlorine level by 1,4 ppm (mg/l).
Quickly dissolving stabilised sanitiser in granular form for shock treatment and continuous disinfection in hard and soft water
Shock treatment/ presence of algae: 50-80 g per 10 m³.
Continuous disinfection: 20-30 g per 10 m³ every one or two days.
Maintain the chlorine level between 1 and 2 mg/l (ppm). 17 g of product in 10 m³ of water will increase the chlorine level by 1 mg/l (ppm).
Quickly dissolving effervescent stabilised sanitiser tablets of 20 g for shock treatment and continuous disinfection
At the beginning of the season or in case of shock treatment or visible algae: 3-5 tablets per 10 m³ of water (in addition to the dosage for continuous treatment).
After a shock treatment do not use the swimming pool for several hours.
1 Tablet in 10 m³ of water will increase the chlorine level by 1 mg/l (ppm).
Slowly dissolving stabilised sanitiser in granular form, recommended for use as local algaecide.
First brush the affected areas thoroughly. Than pour some 20-40 g of the slow dissolving granules onto the affected area. The next day brush again. Repeat this treatment if necessary.
Warning: dependent on the pool coating discolouration may occur.
Slowly dissolving stabilised sanitiser in tablets of 20 g.
10 tablets for 30-35 m³ of pool water every 3-5 days. Dosage may vary widely (sunlight, bathing-load etc.).
Maintain the chlorine level between 1 and 2 mg/l (ppm).
Slowly dissolving stabilised sanitiser in tablets of 200 g
One tablet for 30-35m³ of pool water every 5-8 days. Dosage may vary widely (sunlight, bathing-load etc.).
Maintain the chlorine level between 1 and 2 mg/l (ppm).
Slowly dissolving stabilised sanitiser in tablets of 500 g
One tablet for 30-40m³ of pool water every 15-20 days. Dosage may vary widely (sunlight, bathing-load etc.).
Maintain the chlorine level between 1 and 2 mg/l (ppm).
Organic chlorine tablets (200 g) with 4 functions: disinfection, chlorine stabilisation, algaecidal and flocculent.
It should be added via the skimmer or suitable floating device. Do not throw the tablet directly into the swimming pool.
Dosage: 1 tablet for 30-35 m³ of pool water every 3-5 days. Dosage may vary widely (sunlight, bathing-load etc.). Maintain the chlorine level between 2 and 5 ppm. Generally, the pH should be maintained between 7.2 and 7.6.
Non-chlorine shock treatment to remove organic dirt.
Once a week; 200 g per 10m³.
Bromine tablets for use in whirlpools and indoor pools.
Maintain free bromine level between 3 - 4 ppm.
For shock treatment and continuous disinfection. Suitable for use in hard and soft water
18 g increases the chlorine content of 10m³ by about 1 ppm. Maintain free chlorine level between 2 - 3 ppm.
To decrease the pH of pool water.
80 g (50 ml) of this product in 10 m³ of water will decrease the pH by 0,1.
To increase the pH of pool water.
80 g (80 ml) of this product in 10 m³ of water will increase the pH by 0,1.
Do not add more than 300 g/10 m³ of water during each treatment.
To increase the total alkalinity of the pool water.
150 g of this product into 10 m³ of water will increase the TA by 10 ppm.
Do not add more than 300 g/10 m³ of water during each treatment.
Liquid flocculant, it coagulates suspended particles, which are too small for the filter. The flocs formed are big enough to be retained by the filter.
Once or several times a week 10 ml for 10 m³ of water. In case of high turbidity the dosage may be doubled or tripled.
An excessive dose should be avoided, since this may have an adverse effect
Liquid flocculant, it coagulates suspended particles, which are too small for the filter. The flocs formed are big enough to be retained by the filter.
Once or several times a week 10 ml for 10 m³ of water. In case of high turbidity the dosage may be doubled or tripled.
An excessive dose should be avoided, since this may have an adverse effect.
Gel cubes for continuous flocculation. Highly suitable for pools with underwater lights. The water really becomes crystal-clear.
Place Super Cube in the skimmer. If many leaves are blown into the pool, it is recommendable to put the Super Cube into the supplementary bag and to place the bag into the skimmer. Otherwise, the leaves will stick to the Super Cube. 1 Super Cube per 40 m3 will last for approx. 4 weeks.
Flocculation cartouches for contamination that cannot be removed by a filtration system.
1 cartouche for 20-40 m3 of water, depending on the degree of contamination.
Algaecide to prevent algae growth and to get rid of existing algae
To prevent algae: Initial treatment of 50 ml for 10 m³ of water. After that 20-30 ml for 10 m³ of water every week.
In case of visible algae (greenish water):
First carry out a shock treatment with chlorine. After that, dose 100-150 ml of the product for 10 m³ of water.
Never overdose!
Non-foaming algaecide for whirlpools and swimming pools
To prevent algae:
First treatment of 50 ml for 10 m³ of pool water.
After that 30 ml for 10 m³ of water every week for indoor pools and 50 ml for 10 m³ of water for outdoor pools.
In case of visible algae (greenish water :
First carry out a shock treatment with chlorine. After that, dose 250 ml of the product per 10 m³ of water. After treatment the water should circulate for 1 hour, then the pump should be stopped for 2 hours.
Never overdose!
Stain and scale inhibitor.
For preventive maintenance of 10 m³ of water:
water hardness 350-500 ppm (25-35 English degrees): 100 ml every 3 months.
water hardness 500-750 ppm (35-53 English degrees): 200 ml every 2 months.
water hardness > 750 ppm (53 English degrees): 200 ml each month.
To remove stains or scale deposits dose 200 ml as close as possible to the affected area and brush vigorously the scaled areas.
To increase calcium hardness.
144 g of product will increase the calcium hardness of 10 m³ of water by 10 ppm (mg/l), which is equal to 0,7 English degree.
For each treatment, do not dose more than 750 g per 10 m³ of water.
Stabiliser in order to reduce chlorine dissipation because of UV radiation of the sun. Should not be used in combination with stabilised disinfectants or bromine.
100 g of stabiliser in 10 m³ of water will increase the concentration by 10 mg/l.
Avoid concentrations over 100 mg/l.
Winter care product to condition the pool water during winter, or when the pool is not in use for a long time.
If maintenance stops for max. 3 weeks: 80 ml for 10 m³ of water.
During winter: 150 ml for 10 m³ of water. If possible add 50 ml per 10 m³ of water after about 3 months.